Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

WHITE KNIGHT TUB & TILE

NFPA

PRODUCT USE

Base or Part A of a 2 pack and Hardener or Part B of a 2 pack epoxy coating system.
Requires that the two parts be mixed by hand or mixer before use, in accordance with
manufacturers directions. Mix only as much as is required. Do not return the mixed
material to the original containers. Application is usually by spray atomisation in a
ventilated spray booth, after viscosity reduction with thinner may also be applied by
brush or hand roller. The use of a quantity of material in an unventilated or confined
space may result in increased exposure and an irritating atmosphere developing.Before
starting consider control of exposure by mechanical ventilation.

SYNONYMS

"Epoxy Resin polyamide cured coating Part A Part B"

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

Causes burns.
Risk of serious damage to eyes.
May cause SENSITIZATION by skin contact.
HARMFUL - May cause lung damage if swallowed.
Harmful by inhalation, in contact with skin and if swallowed.
Flammable.
Vapors may cause dizziness or suffocation.
Toxic to aquatic organisms, may cause long- term adverse effects in the aquatic
environment.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  Accidental ingestion of the material may be harmful; animal experiments indicate that ingestion of less than 150 gram may be fatal or may produce serious damage to the health of the individual.  The material can produce chemical burns within the oral cavity and gastrointestinal tract following ingestion.  Considered an unlikely route of entry in commercial/industrial environments.  Ingestion may result in nausea, pain, vomiting. Vomit entering the lungs by aspiration may cause potentially lethal chemical pneumonitis.  

EYE

  The material can produce chemical burns to the eye following direct contact. Vapors or mists may be extremely irritating.  If applied to the eyes, this material causes severe eye damage.  The vapour when concentrated has pronounced eye irritation effects and this gives some warning of high vapour concentrations. If eye irritation occurs seek to reduce exposure with available control measures, or evacuate area.  The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.  

SKIN

  Skin contact with the material may be harmful; systemic effects may resultfollowing absorption.  The material can produce chemical burns following direct contactwith the skin.  Epoxy materials may cause allergic and/or contact dermatitis responses, which may occur on exposure or may become apparent only after repeated exposures. Sensitization is possible. Photoallergic dermatitis may result from contact with the material. This type of response can be elicited only in individuals who have been previously allergically sensitized to the chemical agent and appropriate radiation. Photoallergic dermatitis presents, clinically, as an eczematous dermatitis in sun-exposed areas.  Sensitization reactions may appear suddenly after repeatedsymptom free exposures.  Polyamide hardeners have much reduced volatility, toxicity and are much less irritating to the skin and eyes than amine hardeners. However commercial polyamides may contain a percentage of residual unreacted amine and all unnecessary contact should be avoided.  Toxic effects may result from skin absorption.  Exposure limits with "skin" notation indicate that vapor and liquid may be absorbed through intact skin. Absorption by skin may readily exceed vapor inhalation exposure. Symptoms for skin absorption are the same as for inhalation. Contact with eyes and mucous membranes may also contribute to overall exposure and may also invalidate the exposure standard.  The material may cause severe skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin. Repeated exposures may produce severe ulceration.  

INHALED

  If inhaled, this material can irritate the throat andlungs of some persons.  Inhalation of high concentrations of gas/vapor causes lung irritation with coughing and nausea, central nervous depression with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  Respiratory sensitization may result in allergic/asthma like responses; from coughing and minor breathing difficulties to bronchitis with wheezing, gasping.  

CHRONIC HEALTH EFFECTS

  Skin contact with the material is more likely to cause a sensitization reaction in some persons compared to the general population.  

  Principal routes of exposure are usually by inhalation of vapor/spray mist, inhalation of vapor from the curing material and skin contact with the material.  Sensitization may give severe responses to very low levels of exposure, i.e. hypersensitivity. Sensitized persons should not be allowed to work in situations where exposure may occur.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.