Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

WATTYL IMPERITE 390 PART B

NFPA

PRODUCT USE

Hardener or Part B of a 2 pack. urethane coating system. Requires that the two parts be
mixed by hand or mixer before use, in accordance with manufacturers directions. Mix only
as much as is required. Do not return the mixed material to the original containers.
Application is usually by spray atomisation in a ventilated spray booth, after viscosity
reduction with thinner. CONTAINS free organic isocyanate. Mixing and application requires
special precautions and use of personal protective gear [APMF]. Applied by brush or hand
roller to small areas.

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

Harmful by inhalation.
May cause SENSITIZATION by inhalation and skin contact.
Limited evidence of a carcinogenic effect.
HARMFUL - May cause lung damage if swallowed.
Flammable.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  Although ingestion is not thought to produce harmful effects, the material may still be damaging to the health of the individual following ingestion, especially where pre-  existing organ (e.g. liver, kidney) damage is evident. Present definitions of harmful or toxic substances are generally based on doses producing mortality (death) rather than those producing morbidity (disease, ill-health). Gastrointestinal tract discomfort may produce nausea and vomiting. In an occupational setting however, ingestion of insignificant quantities is not thought to be cause for concern.  Considered an unlikely route of entry in commercial/industrial environments.  

EYE

  There is some evidence to suggest that this material can causeeye irritation and damage in some persons.  The liquid produces a high level of eye discomfort and is capable of causing pain and severe conjunctivitis. Corneal injury may develop, with possible permanent impairment of vision, if not promptly and adequately treated.  The material may produce moderate eye irritation leading to inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.  

SKIN

  The material is not thought to produce adverse health effects or skin irritation following contact (as classified using animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable gloves be used in an occupational setting.  Toxic effects may result from skin absorption.  Bare unprotected skin should not be exposed to this material.  The material may accentuate any pre-existing dermatitis condition.  The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin.  

INHALED

  There is some evidence to suggest that this material, if inhaled, can irritate the throat and lungs of some persons.  The vapor/mist may be highly irritating to the upper respiratory tract and lungs; the response may be severe enough to produce bronchitis and pulmonary edema. Possible neurological symptoms arising from isocyanate exposure include headache, insomnia, euphoria, ataxia, anxiety neurosis, depression and paranoia. Gastrointestinal disturbances are characterized by nausea and vomiting. Pulmonary sensitization may produce asthmatic reactions ranging from minor breathing difficulties to severe allergic attacks; this may occur following a single acute exposure or may develop without warning for several hours after exposure. Sensitized people can react to very low doses, and should not be allowed to work in situations allowing exposure to this material. Continued exposure of sensitized persons may lead to possible long term respiratory impairment.Inhalation hazard is increased at higher temperatures.  Inhalation of high concentrations of gas/vapor causes lung irritation with coughing and nausea, central nervous depression with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  

CHRONIC HEALTH EFFECTS

  There has been concern that this material can cause cancer or mutations, but there is not enough data to make an assessment.  Inhaling this product is more likely to cause a sensitization reaction in some persons compared to the general population.  Skin contact with the material is more likely to cause a sensitization reaction in some persons compared to the general population.  

  Persons with a history of asthma or other respiratory problems or are known to be sensitised, should not be engaged in any work involving the handling of isocyanates. [CCTRADE-Bayer, APMF].  Principal routes of exposure are usually by.  inhalation of vapor/spray mist and skin contact/absorption.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Isocyanate vapors are irritating to the airways and can cause their inflammation, with wheezing, gasping, severe distress, even loss of consciousness and fluid in the lungs. Nervous system symptoms that may occur include headache, sleep disturbance, euphoria, inco-ordination, anxiety, depression and paranoia. Digestive effects include nausea and vomiting. Breathing difficulties may occur unpredictably after a period of tolerance and after skin contact. Allergic inflammation of the skin can occur, with rash, itching, blistering, and swelling of the hands and feet. Sensitive people can react to very low levels and should not be exposed to this material.  Sensitization may give severe responses to very low levels of exposure, i.e. hypersensitivity. Sensitized persons should not be allowed to work in situations where exposure may occur.  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.