Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

WATTYL GALVIT 400 ELECTRO - PART A

NFPA

PRODUCT USE

Part A of a 2 part zinc rich ethyl silicate coating. Manufacturer recommends trained and
experienced operators are needed for blending and application. Requires that the two parts
be mixed by hand or mixer before use, in accordance with manufacturers directions. Mix
only as much as is required. Do not return the mixed material to the original containers.
Application is usually by spray atomisation. The use of a quantity of material in an
unventilated or confined space may result in increased exposure and an irritating
atmosphere developing.Before starting consider control of exposure by mechanical
ventilation.

SYNONYMS

"Part A base two pack zinc dust silicate coating"

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

HARMFUL - May cause lung damage if swallowed.
Harmful by inhalation and in contact with skin.
Irritating to eyes, respiratory system and skin.
Highly flammable.
Harmful to aquatic organisms.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  Although ingestion is not thought to produce harmful effects, the material may still be damaging to the health of the individual following ingestion, especially where pre-  existing organ (e.g. liver, kidney) damage is evident. Present definitions of harmful or toxic substances are generally based on doses producing mortality (death) rather than those producing morbidity (disease, ill-health). Gastrointestinal tract discomfort may produce nausea and vomiting. In an occupational setting however, ingestion of insignificant quantities is not thought to be cause for concern.  Not a likely route of entry into the body in commercial or industrial environments. The liquid may produce considerable gastrointestinal discomfort and be harmful or toxic if swallowed. Ingestion may cause nausea, pain and vomiting. Vomit entering the lungs by aspiration can cause inflammation of the lungs, which can lead to death.  

EYE

  This material can cause eye irritation and damage in some persons.  The liquid produces a high level of eye discomfort and is capable of causing pain and severe conjunctivitis. Corneal injury may develop, with possible permanent impairment of vision, if not promptly and adequately treated.  The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.  

SKIN

  Skin contact with the material may be harmful; systemic effects may resultfollowing absorption.  This material can cause inflammation of the skin oncontact in some persons.  The material may accentuate any pre-existing dermatitis condition.  The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin.  

INHALED

  If inhaled, this material can irritate the throat andlungs of some persons.  Inhalation hazard is increased at higher temperatures.  Inhalation of high concentrations of gas/vapor causes lung irritation with coughing and nausea, central nervous depression with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  

CHRONIC HEALTH EFFECTS

  Principal routes of exposure are usually by inhalation of vapor/spray mist and skin contact with the material.  Xylene is a central nervous system depressant.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.  As with any chemical product, contact with unprotected bare skin; inhalation of vapor, mist or dust in work place atmosphere; or ingestion in any form, should be avoided by observing good occupational work practice.  Welding or flame cutting of metals with zinc or zinc dust coatings may result in inhalation of zinc oxide fume; high concentrations of zinc oxide fume may result in "metal fume fever"; also known as "brass chills", an industrial disease of short duration. [I.L.O] Symptoms include malaise, fever, weakness, nausea and may appear quickly if operations occur in enclosed or poorly ventilated areas.