Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

WATTYL VERSACOR BASECOAT PART B

NFPA

PRODUCT USE

Part B or Hardener of a 2 pack epoxy coating system. · Material is mixed and used in
accordance with manufacturers directions. The use of a quantity of material in an
unventilated or confined space may result in increased exposure and an irritating
atmosphere developing.

SYNONYMS

"Epoxy Part B hardener two part paint coil coat metal primer coating"

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

Harmful in contact with skin.
Causes burns.
Risk of serious damage to eyes.
May cause SENSITIZATION by skin contact.
Flammable.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  The material can produce chemical burns within the oral cavity and gastrointestinal tract following ingestion.  Not a likely route of entry into the body in commercial or industrial environments. The liquid may produce considerable gastrointestinal discomfort and be harmful or toxic if swallowed. Ingestion may cause nausea, pain and vomiting. Vomit entering the lungs by aspiration can cause inflammation of the lungs, which can lead to death.  

EYE

  The material can produce chemical burns to the eye following direct contact. Vapors or mists may be extremely irritating.  If applied to the eyes, this material causes severe eye damage.  The liquid produces a high level of eye discomfort and is capable of causing pain and severe conjunctivitis. Corneal injury may develop, with possible permanent impairment of vision, if not promptly and adequately treated.  The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.  

SKIN

  Skin contact with the material may be harmful; systemic effects may resultfollowing absorption.  The material can produce chemical burns following direct contactwith the skin.  Polyamide hardeners have much reduced volatility, toxicity and are much less irritating to the skin and eyes than amine hardeners. However commercial polyamides may contain a percentage of residual unreacted amine and all unnecessary contact should be avoided.  Exposure limits with "skin" notation indicate that vapor and liquid may be absorbed through intact skin. Absorption by skin may readily exceed vapor inhalation exposure. Symptoms for skin absorption are the same as for inhalation. Contact with eyes and mucous membranes may also contribute to overall exposure and may also invalidate the exposure standard.  Epoxy materials may cause allergic and/or contact dermatitis responses, which may occur on exposure or may become apparent only after repeated exposures. Sensitization is possible. Photoallergic dermatitis may result from contact with the material. This type of response can be elicited only in individuals who have been previously allergically sensitized to the chemical agent and appropriate radiation. Photoallergic dermatitis presents, clinically, as an eczematous dermatitis in sun-exposed areas.  Sensitization may result in allergic dermatitis responses includingrash, itching, hives or swelling of extremities.  Sensitization reactions may appear suddenly after repeatedsymptom free exposures.  The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin.  Bare unprotected skin should not be exposed to this material.  The material may accentuate any pre-existing dermatitis condition.  

INHALED

  Inhalation may produce health damage*.  If inhaled, this material can irritate the throat andlungs of some persons.  Inhalation hazard is increased at higher temperatures.  Acute effects from inhalation of high vapor concentrations may be chest and nasal irritation with coughing, sneezing, headache and even nausea.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  Inhalation of vapor may aggravate a pre-existing respiratory condition such as asthma, bronchitis, emphysema.  

CHRONIC HEALTH EFFECTS

  Skin contact with the material is more likely to cause a sensitization reaction in some persons compared to the general population.  

  Principal routes of exposure are usually by inhalation of vapor and skin contact with the material.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Sensitization may give severe responses to very low levels of exposure, i.e. hypersensitivity. Sensitized persons should not be allowed to work in situations where exposure may occur.  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.  As with any chemical product, contact with unprotected bare skin; inhalation of vapor, mist or dust in work place atmosphere; or ingestion in any form, should be avoided by observing good occupational work practice.